Optimum Gas Journal Bearing with Open Bearing Ends and Feeder Slot

The optimum design of the cylindrical outer contours of a gas journal bearing is obtained using the methods of the calculus of variations with allowance for the lubricant leakage through the bearing ends and the feeder slot when the lubricant mass in the working gap is conserved. The variational problem of designing the clearance shape giving the maximum bearing load capacity is formulated and solved. A modified Elrod-Burgdorfer condition for the pressure is used.     

Experimental Study of the Dynamic Effect of an Internal Solitary Wave on a Submerged Circular Cylinder

The hydrodynamic loads due to the interaction of a small-amplitude internal solitary wave with a submerged circular cylinder in a two-layer system of miscible fluids were studied experimentally. The dependence of the internal-wave transmission coefficient on the position of the center of the cylinder relative to the pycnocline and on the ratio of the cylinder diameter to the fluid-layer thickness was obtained. The effects of the pycnocline thickness and the depth of the center of the cylinder on the value of the hydrodynamic loads were studied. Visualization of the flow structure was performed. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 46, No. 6, pp. 36–44, November–December, 2005.     

Use of the reciprocity theorem for axially symmetric transient problems

Summary A fundamental solution, to be used in reciprocal theorem for the solutions of axially symmetric transient problem of elastodynamics, is presented. A cylindrical cavity problem has been solved to check the formulation. The strong singularity of the resulting integral equation for this problem has been reduced to the weak form. The new formulation provides the initial velocity on the surface for a transient loading. Some differences have been introduced for the use of generalized functions.     

T300/648迭层板接头挤压疲劳损伤参数的选择与测定

本文对碳纤维增强复合材料迭层板(C.F.R.P)接头在不同环境条件下的挤压疲劳损伤扩展进行了实验研究.并根据“剩余强度,剩余刚度”理论和“疲劳模量”概念,讨论了接头的刚度下降和强度变化.由此提出了“损伤参数”D的定义和测量方法;并对损伤试件,进行了X射线检测分析,验证了累积损伤的扩展.     

软夹硬力学不均匀焊接接头疲劳裂纹闭合行为的实验研究

力学性能不均匀是焊接接头的三大待征之一，本文采用柔度法研究了不同硬夹层宽度的软夹硬力学不均匀焊接接头疲劳裂纹的闭俣行为。研究结果表明，裂纹尖端附近软区的局部屈服在疲劳载荷卸载过程中促使裂纹闭合。随着硬夹层宽度的减小，这一影响越来越明显。     

自动检测da/dN的微机系统

研制了一种da/dN自动检测系统;介绍了其工作原理和裂纹长度a及循环数N的采集方法;与传统的目测法做了对比;显示了该系统的优越性。     

A fast algorithm for soil dynamics calculations by wavelet decomposition

Summary The article presents a fast numerical algorithm for calculating the response of a halfspace under any surface loads. Under certain conditions there exists an analytical solution to the problem in the Fourier domain. To get the desired response, a numerical inverse Fourier transform of this analytic solution has to be made. By using a wavelet decomposition, the proposed algorithm can reduce the calculation time significantly, thus allowing the computation of complex problems. As an example, the response of the beam-halfspace coupled system under moving load is presented. Received 6 March 1997; accepted for publication 20 May 1997     

机翼全尺寸延寿试验及可靠性分析

机翼全尺寸疲劳试验是老龄飞机延寿的科学依据。本文介绍了疲劳裂纹形成和扩展寿命的分散系数，以及可靠度和标准差的选取。针对延寿的可靠性分析，提出按疲劳／损伤容限设计概念或当量裂纹扩展寿命方法，以及机翼串联模型，确定整机延寿使用寿命的技术途径。最后给出应用实例。     

可靠性设计中的疲劳裂纹扩展随机模型

首先导出了疲劳裂纹扩展的确定性方程，然后将疲劳裂纹扩展确定性方程随机化，导出了疲劳裂纹随机扩展的概率公式，并推导了疲劳裂纹随机扩展的置信限公式，最后，给出了二种材料疲劳裂纹随机扩展数据的处理结果。     

机车曲轴镀铁修复疲劳对比试验研究

通过对镀铁修复后的机车曲轴的疲劳性能进行检测试验，同时给出参照的新曲轴的疲劳性能参数，比较分析原件性能和镀铁修复后的疲劳性能的差异，从而判断在原工作环境下镀铁修复后机车曲轴的工作寿命如何变化，试验中采用42CrMoA棒材及其镀铁修复件进行比较，给出了最大应力—疲劳寿命的S—N曲线，从实验数据可以分析，因长期使用轴径磨损的曲轴镀铁修复后，其疲劳性能将有部分损失，疲劳极限下降9．68%，这意味着在较大的疲劳应力下工作的镀铁修复后曲轴，其疲劳寿命低于原件，因此应进一步研究镀铁修复的曲轴在实际工况下的疲劳极限，并改善镀铁工艺，提高疲劳极限，使镀铁修复技术更好地应用于工程实际。